vom618a www.vishay.com vishay semiconductors rev. 1.4, 21-oct-13 1 document number: 83449 for technical questions, contact: optocoupleranswe rs@vishay.com this document is subject to change without notice. the products described herein and this document are subject to specific disclaimers, set forth at www.vishay.com/doc?91000 low input current, phototransistor output, sop-4, mini-flat package description the 110 c rated vom618a has a gaas infrared emitting diode emitter, which is optically coupled to a silicon planar phototransistor detector, and is incorporated in a 4 pin 100 mil lead pitch miniflat package. it features a high current transfer ratio with low in put current, low coupling capacitance, and high isolation voltage. these coupling devices are desi gned for signal transmission between two electrically separated circuits. features ? operating temperature from - 55 c to + 110 c ? sop-4 mini-flat package ? ctr range 40 % to 600 %, i f = 1 ma ? isolation test voltage, 3750 v rms ? low saturation voltage ? fast switching times ? low coupling capacitance ? end-stackable, 0.100" (2.54 mm) spacing ? material categorization: for definitions of compliance please see www.vishay.com/doc?99912 applications ?plcs ? telecommunication ? lighting control system ? solar inverters ? ac drives agency approvals (all parts are certified under base model vom618a) ? ul1577, file no. e52744 ? cul tested to csa 22.2 bulletin 5a ? din en 60747-5-5 (vde 0884-5), available with option 1 ? fimko en 60065 and en 60950-1 ? cqc: gb8898-2011, gb4943.1-2011 e c a c 1 2 4 3 i179089 ordering information vom6 1 8a - #x0 0 1 t part number ctr bin vde option tape and reel agency certified/ package ctr (%) 1 ma ul, cul, fimko, cqc 50 to 600 40 to 80 63 to 125 100 to 200 160 to 320 50 to 100 80 to 160 130 to 260 sop-4, mini-flat vom618at VOM618A-1T vom618a-2t vom618a-3t vom618a-4t vom618a-5t vom618a-7t vom618a-8t vde, ul, cul, cqc, fimko 50 to 600 40 to 80 63 to 125 100 to 200 160 to 320 50 to 100 80 to 160 130 to 260 sop-4, mini-flat vom618a- x001t vom618a- 1x001t vom618a- 2x001t vom618a- 3x001t vom618a- 4x001t vom618a- 5x001t vom618a- 7x001t vom618a- 8x001t s op-4 5
vom618a www.vishay.com vishay semiconductors rev. 1.4, 21-oct-13 2 document number: 83449 for technical questions, contact: optocoupleranswe rs@vishay.com this document is subject to change without notice. the products described herein and this document are subject to specific disclaimers, set forth at www.vishay.com/doc?91000 notes ? stresses in excess of the absolu te maximum ratings can ca use permanent damage to the device. functional operation of the devic e is not implied at these or any other conditions in excess of those give n in the operational sections of this document. exposure to abs olute maximum ratings for extended periods of th e time can adversely affect reliability. (1) see assembly instructions for surface mounted devices ( www.vishay.com/doc?80054 ). fig. 1 - total power dissipation vs. ambient temperature absolute maximum ratings (t amb = 25 c, unless otherwise specified) parameter test condition symbol value unit input dc forward current i f 60 ma reverse voltage v r 6v power dissi pation p diss 70 mw surge forward current t p 10 s i fsm 2.5 a output collector emitter voltage v ceo 80 v emitter collector voltage v eco 7v collector current i c 50 ma t p 1 ms i c 100 ma power dissi pation p diss 150 mw coupler isolation test volt age between emitter and detector t = 1 min v iso 3750 v rms total power dissipation p tot 170 mw operating temperature range t amb - 55 to + 110 c storage temperature range t stg - 55 to + 150 c junction temperature t j 125 c soldering temperature (1) t sld 260 c 0 50 100 150 200 0 25 50 75 100 125 p tot - total power di ss ipation (mw) t amb - ambient temperature ( c) coupled device phototran s i s tor ir-diode
vom618a www.vishay.com vishay semiconductors rev. 1.4, 21-oct-13 3 document number: 83449 for technical questions, contact: optocoupleranswe rs@vishay.com this document is subject to change without notice. the products described herein and this document are subject to specific disclaimers, set forth at www.vishay.com/doc?91000 note ? minimum and maximum values are testing requirements. typical values are characteristics of the device and are the result of en gineering evaluation. typical values are for information only and are not part of the testing requirements. electrical characteristics (t amb = 25 c, unless otherwise specified) parameter test condition symbol min. typ. max. unit input forward voltage i f = 5 ma v f 1.1 1.6 v reverse current v r = 6 v i r 0.01 10 a capacitance v r = 0 v, f = 1 mhz c j 9pf output collector emitter leakage current v ce = 20 v i ceo 0.4 100 na collector emitter breakdown voltage i c = 100 a bv ceo 80 v emitter collector breakdown voltage i e = 10 a bv eco 7v collector emitte r capacitance v ce = 5 v, f = 1 mhz c ce 2.8 pf coupler coupling capaci tance f = 1 mhz c c 0.3 pf collector emitter sa turation voltage i f = 1 ma, i c = 0.25 ma v cesat 0.12 0.4 v cut-off frequency i f = 10 ma, v cc = 5 v, r l = 100 f ctr 110 khz current transfer ratio (t amb = 25 c, unless otherwise specified) parameter test condition part symbol min. typ. max. unit i c /i f i f = 1 ma, v ce = 5 v vom618a ctr 50 600 % vom618a-1 ctr 40 80 % vom618a-2 ctr 63 125 % vom618a-3 ctr 100 200 % vom618a-4 ctr 160 320 % vom618a-5 ctr 50 100 % vom618a-7 ctr 80 160 % vom618a-8 ctr 130 260 % switching characteristics (t amb = 25 c, unless otherwise specified) parameter test condition symbol min. typ. max. unit non-saturated rise and fall time i c = 2 ma, v cc = 5 v, r l = 100 t r 5s fall time t f 4s turn-on time t on 7s turn-off time t off 6s saturated rise and fall time i f = 1.6 ma, v cc = 5 v, r l = 4.7 k t r 6s fall time t f 29 s turn-on time t on 8s turn-off time t off 35 s
vom618a www.vishay.com vishay semiconductors rev. 1.4, 21-oct-13 4 document number: 83449 for technical questions, contact: optocoupleranswe rs@vishay.com this document is subject to change without notice. the products described herein and this document are subject to specific disclaimers, set forth at www.vishay.com/doc?91000 fig. 2 - test circuit fig. 3 - test circuit and waveforms note ? as per din en 60747-5-5 (vde 0884), 7.4.3.8.2, this optocoupler is suitable for safe electrical insulation only within the safety ratings. compliance with the safety ra tings shall be ensured by means of protective circuits. typical characteristics (t amb = 25 c, unless otherwise specified) fig. 4 - forward voltage vs. forward current fig. 5 - collector current vs. collector emitter voltage (non-saturated) input v out v cc = 5 v r l 10 % 90 % input pulse output pulse t r t on t f t off safety and insulation ratings parameter symbol value unit maximum safety ratings output safety power p so 300 mw input safety current i si 200 mw safety temperature t s 150 c comparative tracking index cti 175 insulation rated parameters maximum withstanding isolation voltage v iso 3750 v rms maximum transient isolation voltage v iotm 6000 v peak maximum repetitive pe ak isolation voltage v iorm 565 v peak insulation resistance t amb = 25 c, v dc = 500 v r io 10 12 isolation resistance t amb = 100 c, v dc = 500 v r io 10 11 climatic classification (a ccording to iec 68 part 1) 55/110/21 environment (pollution degree in accordance to din vde 0109) 2 internal creepage 5 mm external creepage 5 mm clearance 5 mm insulation thickness 0.4 mm 0.1 1 10 100 0.6 0.8 1.0 1.2 1.4 1.6 i f - forward current (ma) v f - forward voltage (v) t amb = 110 c t amb = 75 c t amb = 25 c t amb = 0 c t amb = - 55 c 0 10 20 30 40 50 0 1 2 3 4 5 6 7 8 9 10 i c - collector current (ma) v ce - collector emitter voltage (non- s at) (v) i f = 1 ma i f = 10 ma i f = 5 ma i f = 15 ma i f = 20 ma i f = 25 ma
vom618a www.vishay.com vishay semiconductors rev. 1.4, 21-oct-13 5 document number: 83449 for technical questions, contact: optocoupleranswe rs@vishay.com this document is subject to change without notice. the products described herein and this document are subject to specific disclaimers, set forth at www.vishay.com/doc?91000 fig. 6 - collector emitter current vs. ambient temperature fig. 7 - collector current vs. collector emitter voltage (saturated) fig. 8 - collector emitter voltage vs. ambient temperature (saturated) fig. 9 - normalized current transfer ratio vs. ambient temperature (saturated) fig. 10 - normalized current transfer ratio vs. ambient temperature (non-saturated) fig. 11 - current transfer rati o vs. forward current (saturated) normalized to 1 ma at 25 c 0.001 0.01 0.1 1 10 100 1000 10 000 - 60 - 40 - 20 0 20 40 60 80 120 i ce0 - leakage current (na) t amb - ambient temperature ( c) i f = 0 ma v ce = 40 v v ce = 24 v v ce = 12 v 100 0 5 10 15 20 25 30 35 0.0 0.1 0.2 0.3 0.4 i c - collector current (ma) v ce - collector emitter voltage (v) i f = 25 ma i f = 10 ma i f = 0.5 ma i f = 2 ma i f = 5 ma i f = 1 ma 0.00 0.02 0.04 0.06 0.08 0.10 0.12 - 60 - 40 - 20 0 20 40 60 80 100 120 v ce s at - collector emitter voltage (v) t amb - ambient temperature ( c) i f = 1 ma 0 0.2 0.4 0.6 0.8 1.0 1.2 1.4 - 60 - 40 - 20 0 20 40 60 80 100 120 n ctr - normalized ctr ( s at) t amb - ambient temperature ( c) normalized to ctr value: i f = 1 ma, v ce = 5 v, t amb = 25 c 0 0.2 0.4 0.6 0.8 1.0 1.2 1.4 - 60 - 40 - 20 0 20 40 60 80 100 120 n ctr - normalized ctr (non- s aturated) t amb - ambient temperature ( c) normalized to ctr value: i f = 1 ma, v ce = 5 v, t amb = 25 c 0.0 0.2 0.4 0.6 0.8 1.0 1.2 1.4 1.6 1.8 2.0 0.1 1 10 100 n ctr - normalized ctr ( s at) i f - forward current (ma) t amb = 0 c t amb = - 55 c t amb = 25 c t amb = 110 c
vom618a www.vishay.com vishay semiconductors rev. 1.4, 21-oct-13 6 document number: 83449 for technical questions, contact: optocoupleranswe rs@vishay.com this document is subject to change without notice. the products described herein and this document are subject to specific disclaimers, set forth at www.vishay.com/doc?91000 fig. 12 - current transfer ratio vs. forward current (non-saturated) normalized to 1 ma at 25 c fig. 13 - cut-off frequency (- 3 db) vs. collector current fig. 14 - f ctr vs. phase angle fig. 15 - switching time vs. load resistance fig. 16 - voltage gain vs. cut-off frequency 0.0 0.5 1.0 1.5 2.0 2.5 0.1 1 10 100 n ctr - normalized ctr (n s ) i f - forward current (ma) t amb = 0 c t amb = 110 c t amb = - 55 c t amb = 25 c 1000 0.1 f ctr - cut-off-frequency (khz) 100 10 1 1 10 100 i c - collector current (ma) v ce = 5 v, t amb = 25 c - 160 - 140 - 120 - 100 - 80 - 60 - 40 - 20 0 1 10 100 1000 pha s e angle (deg) f - cut-off fre q uency (khz) v ce = 5 v r l = 1000 r l = 100 1 10 100 1000 0 5 10 15 20 t on , t off - s witching time ( s ) r l - load re s i s tance (k ) t on ( s ) t off ( s ) i f = 1 ma v ce = 5 v - 40 - 35 - 30 - 25 - 20 - 15 - 10 - 5 0 1 10 100 1000 voltage g ain f - cut-off fre q uency (khz) v ce = 5 v r l = 100 r l = 1000
vom618a www.vishay.com vishay semiconductors rev. 1.4, 21-oct-13 7 document number: 83449 for technical questions, contact: optocoupleranswe rs@vishay.com this document is subject to change without notice. the products described herein and this document are subject to specific disclaimers, set forth at www.vishay.com/doc?91000 package dimensions in millimeters package marking (example of vom618a-3x001t) notes ? only option 1 is reflected in the pa ckage marking with the character x. ? tape and reel suffix (t) is not part of the package marking. tape and reel dimensions in millimeters fig. 17 - reel dimensio ns (3000 units per reel) fi g. 18 - tape dimensions 4.40 0.2 2.54 0.25 1 4 2 3 pin one id 3.85 0.3 2.00 0.2 0.10 0.1 0.40 0.1 0.8 6.5 2.54 1 0.40 0.1 7.00 + 0.2 - 0.7 5.30 0.3 0.2 0.05 i178048 618a3 v yww 25x 330 (13 " ) 100 17.1 12 0.3 4 0.1 5.5 0.1 2 0.1 1.75 0.1 1.5 0.1 8 0.1 0.3 0.05 2.45 0.1
legal disclaimer notice www.vishay.com vishay revision: 08-feb-17 1 document number: 91000 disclaimer ? all product, product specifications and data ar e subject to change with out notice to improve reliability, function or design or otherwise. vishay intertechnology, inc., its affiliates, agents, and employee s, and all persons acting on it s or their behalf (collectivel y, vishay), disclaim any and all liability fo r any errors, inaccuracies or incompleteness contained in any datasheet or in any o ther disclosure relating to any product. vishay makes no warranty, representation or guarantee regarding the suitability of th e products for any particular purpose or the continuing production of any product. to the maximum extent permitted by applicable law, vi shay disclaims (i) any and all liability arising out of the application or use of any product , (ii) any and all liability, including without limitation specia l, consequential or incidental damages, and (iii) any and all implied warranties, includ ing warranties of fitness for particular purpose, non-infringement and merchantability. statements regarding the suitability of products for certain types of applicatio ns are based on vishays knowledge of typical requirements that are often placed on vishay products in generic applications. such statements are not binding statements about the suitability of products for a particular applic ation. it is the customers responsibility to validate tha t a particular product with the prope rties described in the product sp ecification is suitable for use in a particular application. parameters provided in datasheets and / or specifications may vary in different ap plications and perfor mance may vary over time. all operating parameters, including ty pical parameters, must be va lidated for each customer application by the customer s technical experts. product specifications do not expand or otherwise modify vishays term s and conditions of purchase, including but not limited to the warranty expressed therein. except as expressly indicated in writing, vishay products are not designed for use in medical, life-saving, or life-sustaining applications or for any other application in which the failure of the vishay product could result in personal injury or death. customers using or selling vishay product s not expressly indicated for use in such applications do so at their own risk. please contact authorized vishay personnel to obtain writ ten terms and conditions rega rding products designed for such applications. no license, express or implied, by estoppel or otherwise, to any intellectual property rights is gran ted by this document or by any conduct of vishay. product names and markings noted herein may be trademarks of their respective owners. ? 2017 vishay intertechnology, inc. all rights reserved
|
